Is it possible to send the hint from OPNsense itself?
Yes, to me it sounds like you’re already getting a big enough prefix from your ISP (all devices getting a /64), but you’ll have to request a bigger prefix from OPNsense. I believe it should give you the options to do this when you set the IPv6 mode to DHCPv6 on OPNsense, but I can’t say if your ISP router will handle it.
I have also added all Cloudflare IPs in Jellyfin’s known proxies
You should only need to add the IP of the last proxy before reaching Jellyfin, which would be Caddy.
If you can’t get the VPS to work, alternatively there’s Cloudflare but last I checked streaming was a little out of their free terms. With it, you should just have to set your AAAA record and make the cloud orange, that way Cloudflare will proxy it, and IPv4 will work. There’s also Cloudflare tunnels which lets you host websites without port forwarding anything.
I’ve got a catch-all setup to go straight to my spam folder, OP could do something similar.
I can’t wait for it to be added to activate-linux!
Sure it let’s you use it asynchronously, but it predates and is not really compatible with JavaScript’s async/Promise API.
Debian testing has ‘updated’ to 5.6.1+really5.4.5-1 anyway, so as long as you’ve updated within the past few days it will have been downgraded to 5.4.5.
In theory PWAs can be configured to run offline, whether they’re doing that I don’t know.
The desktop app looks like it’s electron though.
That’s not really your code, more so you haven’t setup a .gitignore to not commit not your code.
ZLUDA originally only supported on Intel since it was designed by an Intel employee, but AMD hired him to make it work for AMD instead. So in a way Intel is somewhat important here.
And I really should get used to how debian works with
su.
I only know because installing sudo is usually the very first thing I do whenever I have to install it haha.
I might be wrong, but I believe Debian ships without sudo, only su by default (or at least if you configure a root password in the setup).
I’ve run kill -9 and similar heaps before, but weirdly this comment reminded me of this: https://youtu.be/Fow7iUaKrq4
IEEE Spectrum says this:
Currently, he says, the new discs have a writing speed of about 100 milliseconds and an energy consumption of microjoules to millijoules.
Idk if that means the full 200TB in 100ms, or a bit per 100ms, but there is a number out there I suppose.
A lot of external status services just send a HTTP request to a certain url, if it succeeds then it’s up, if it errors or times out then it’s down. They also usually let you check if TCP ports do the usual handshake thing if you aren’t using HTTP.
The response time can also be used to check if a site is running slower than usual too, and if you have a use for it you can usually specify the required response code for success.
Although I wouldn’t be surprised if GitHub has some per-server analytics they can also use to estimate the load, but Instatus would work as described above.
Sometimes these sorts of things are referred to as health checks, if you’re looking for search terms. For example Docker can be set up to poll a container’s web server every few minutes, and mark it as unhealthy it if it stops replying using the HEALTHCHECK instruction in the Dockerfile.
Nah, apparently it’s completely valid to end IPv6 addresses with a 0. And I haven’t done much research, but it seems IPv6 really doesn’t have network addresses the way IPv4 does.
Also you can ping them and they reply.
Some discord servers can require a verified phone number, not any I know of, but it can be enabled.
On the ISO keyboards I’ve seen, the enter key has way more than double the surface area than ANSI, so it’s definitely not ‘just rotated 90 degrees’. Also these people probably grew up with ISO and struggle with ANSI, just like you probably grew up with ANSI and struggle with ISO.
I doubt this will be any use, but my Telstra 4G has a public IPv6.
If the HOA’s router supports UPnP/NAT-PMP/PCP then you might be able to use that to get some ports forwarded.